# generated by Slic3r 1.34.1-prusa3d-win64 on Wed Oct 25 10:49:33 2017

[filament:ABS]
bed_temperature = 90
bridge_fan_speed = 0
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 0.86
fan_always_on = 0
fan_below_layer_time = 5
filament_colour = #FFFFFF
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 5
filament_notes = "Warping medio, evitar corrientes de aire mientras imprime. Temperatura de la base, minimo 90ºC."
filament_settings_id = 
first_layer_bed_temperature = 90
first_layer_temperature = 245
max_fan_speed = 0
min_fan_speed = 0
min_print_speed = 10
slowdown_below_layer_time = 20
temperature = 245

[filament:ABS PLUS]
bed_temperature = 75
bridge_fan_speed = 0
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 0.95
fan_always_on = 0
fan_below_layer_time = 5
filament_colour = #FFFFFF
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 5
filament_notes = ""
filament_settings_id = 
first_layer_bed_temperature = 75
first_layer_temperature = 242
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 20
temperature = 242

[filament:FLEXIPRINT]
bed_temperature = 40
bridge_fan_speed = 0
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 1.15
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #303030
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 5
filament_notes = "Apretar minimamente la muletilla, lo justo para que empiece a extruir."
filament_settings_id = 
first_layer_bed_temperature = 40
first_layer_temperature = 232
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 5
slowdown_below_layer_time = 15
temperature = 232

[filament:HIPS]
bed_temperature = 90
bridge_fan_speed = 0
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 0.9
fan_always_on = 0
fan_below_layer_time = 5
filament_colour = #FFFFFF
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 5
filament_notes = ""
filament_settings_id = 
first_layer_bed_temperature = 90
first_layer_temperature = 250
max_fan_speed = 0
min_fan_speed = 0
min_print_speed = 10
slowdown_below_layer_time = 20
temperature = 250

[filament:METÄL]
bed_temperature = 0
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 1.1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #808000
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 8
filament_notes = "Altura minima de capa recomendable 0.18mm.\nEchar muy poco spray adherente en la base. Practicamente nada."
filament_settings_id = 
first_layer_bed_temperature = 0
first_layer_temperature = 210
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 15
temperature = 210

[filament:NYLON CARBONO]
bed_temperature = 90
bridge_fan_speed = 0
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 0.91
fan_always_on = 0
fan_below_layer_time = 10
filament_colour = #FFFFFF
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 5
filament_notes = ""
filament_settings_id = 
first_layer_bed_temperature = 90
first_layer_temperature = 220
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 10
slowdown_below_layer_time = 20
temperature = 220

[filament:PETG]
bed_temperature = 70
bridge_fan_speed = 0
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 0.91
fan_always_on = 0
fan_below_layer_time = 10
filament_colour = #FFFFFF
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
first_layer_bed_temperature = 70
first_layer_temperature = 220
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 10
slowdown_below_layer_time = 10
temperature = 220

[filament:PLA]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 0.86
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFF00
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
first_layer_bed_temperature = 50
first_layer_temperature = 215
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 10
temperature = 215

[filament:PLA Fine]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 0.91
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = ""
filament_settings_id = 
first_layer_bed_temperature = 50
first_layer_temperature = 205
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 10
temperature = 205

[filament:PLA INGEO]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 0.96
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 10
filament_notes = "Impresión sin problemas detectados."
filament_settings_id = 
first_layer_bed_temperature = 50
first_layer_temperature = 205
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 10
temperature = 205

[filament:PP]
bed_temperature = 90
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 2
extrusion_multiplier = 0.89
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #303030
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 5
filament_notes = "Reomcendable: Infill alto, mas de 50%"
filament_settings_id = 
first_layer_bed_temperature = 90
first_layer_temperature = 220
max_fan_speed = 100
min_fan_speed = 50
min_print_speed = 10
slowdown_below_layer_time = 20
temperature = 190

[filament:WOÖD]
bed_temperature = 30
bridge_fan_speed = 100
cooling = 1
disable_fan_first_layers = 0
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #808000
filament_cost = 0
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 8
filament_notes = "No imprimir capas de menos de 0.15mmRecomendable mas de 0.18mm.\nEchar muy poco Spray adherente en la base."
filament_settings_id = 
first_layer_bed_temperature = 30
first_layer_temperature = 210
max_fan_speed = 100
min_fan_speed = 100
min_print_speed = 10
slowdown_below_layer_time = 10
temperature = 210

[presets]
filament = PLA INGEO.ini
print = Calidad Buena.ini
printer = Boquilla - 0.4mm.ini

[print:Calidad Buena]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 1000
bridge_flow_ratio = 0.8
bridge_speed = 60
brim_width = 0
clip_multipart_objects = 0
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
ensure_vertical_shell_thickness = 0
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 25
external_perimeters_first = 1
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.4
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.6
first_layer_height = 0.3
first_layer_speed = 50%
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 1000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.6
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 10%
infill_speed = 50
interface_shells = 0
layer_height = 0.18
max_print_speed = 200
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 1000
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 25
perimeters = 3
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 2
skirt_height = 1
skirts = 2
small_perimeter_speed = 25
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 90
support_material_buildplate_only = 1
support_material_contact_distance = 0.1
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 1.5
support_material_speed = 45
support_material_synchronize_layers = 0
support_material_threshold = 20
support_material_with_sheath = 1
support_material_xy_spacing = 1.5
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 45
top_solid_layers = 6
travel_speed = 180
xy_size_compensation = 0

[print:Calidad Excelente]
avoid_crossing_perimeters = 0
bottom_solid_layers = 8
bridge_acceleration = 1000
bridge_flow_ratio = 0.8
bridge_speed = 60
brim_width = 0
clip_multipart_objects = 0
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
ensure_vertical_shell_thickness = 0
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 30
external_perimeters_first = 1
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.4
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.6
first_layer_height = 0.3
first_layer_speed = 50%
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 1000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.6
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 10%
infill_speed = 50
interface_shells = 0
layer_height = 0.09
max_print_speed = 200
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 1000
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 2
skirt_height = 1
skirts = 2
small_perimeter_speed = 25
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 90
support_material_buildplate_only = 1
support_material_contact_distance = 0.1
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 1.5
support_material_speed = 80
support_material_synchronize_layers = 0
support_material_threshold = 20
support_material_with_sheath = 1
support_material_xy_spacing = 1.5
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 45
top_solid_layers = 10
travel_speed = 180
xy_size_compensation = 0

[print:Calidad Normal]
avoid_crossing_perimeters = 0
bottom_solid_layers = 5
bridge_acceleration = 1000
bridge_flow_ratio = 0.8
bridge_speed = 60
brim_width = 0
clip_multipart_objects = 0
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
ensure_vertical_shell_thickness = 0
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 30
external_perimeters_first = 1
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.4
fill_angle = 45
fill_density = 20%
fill_pattern = honeycomb
first_layer_acceleration = 1000
first_layer_extrusion_width = 0.6
first_layer_height = 0.3
first_layer_speed = 50%
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 1000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.6
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 10%
infill_speed = 55
interface_shells = 0
layer_height = 0.24
max_print_speed = 200
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 1000
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 35
perimeters = 2
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 2
skirt_height = 1
skirts = 2
small_perimeter_speed = 25
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 90
support_material_buildplate_only = 1
support_material_contact_distance = 0.1
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 1.5
support_material_speed = 80
support_material_synchronize_layers = 0
support_material_threshold = 20
support_material_with_sheath = 1
support_material_xy_spacing = 1.5
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 45
top_solid_layers = 5
travel_speed = 180
xy_size_compensation = 0

[print:Especial - Boquilla 0.2]
avoid_crossing_perimeters = 0
bottom_solid_layers = 8
bridge_acceleration = 1000
bridge_flow_ratio = 0.8
bridge_speed = 60
brim_width = 0
clip_multipart_objects = 0
complete_objects = 0
default_acceleration = 1000
dont_support_bridges = 1
ensure_vertical_shell_thickness = 0
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.25
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 1000
first_layer_extrusion_width = 0
first_layer_height = 0.2
first_layer_speed = 50%
gap_fill_speed = 40
gcode_comments = 0
infill_acceleration = 1000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 10%
infill_speed = 50
interface_shells = 0
layer_height = 0.09
max_print_speed = 200
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 1000
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 30
perimeters = 6
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 2
skirt_height = 1
skirts = 2
small_perimeter_speed = 20
solid_infill_below_area = 0
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 50
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 1
support_material_contact_distance = 0.1
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 1
support_material_speed = 50
support_material_synchronize_layers = 0
support_material_threshold = 20
support_material_with_sheath = 0
support_material_xy_spacing = 1
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 45
top_solid_layers = 10
travel_speed = 180
xy_size_compensation = 0

[print:Especial - Flexiprint]
avoid_crossing_perimeters = 0
bottom_solid_layers = 4
bridge_acceleration = 0
bridge_flow_ratio = 0.8
bridge_speed = 25
brim_width = 0
clip_multipart_objects = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
ensure_vertical_shell_thickness = 0
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 70%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extrusion_width = 0.4
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 0.6
first_layer_height = 0.3
first_layer_speed = 50%
gap_fill_speed = 20
gcode_comments = 0
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.6
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 30%
infill_speed = 25
interface_shells = 0
layer_height = 0.18
max_print_speed = 80
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 0
min_skirt_length = 0
notes = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 25
perimeters = 3
post_process = 
print_settings_id = 
raft_layers = 0
resolution = 0
seam_position = aligned
skirt_distance = 2
skirt_height = 1
skirts = 2
small_perimeter_speed = 20
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 25
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 1
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 0
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 1.5
support_material_speed = 25
support_material_synchronize_layers = 0
support_material_threshold = 20
support_material_with_sheath = 0
support_material_xy_spacing = 1.5
thin_walls = 1
threads = 4
top_infill_extrusion_width = 0
top_solid_infill_speed = 25
top_solid_layers = 5
travel_speed = 180
xy_size_compensation = 0

[printer:Boquilla - 0.2mm]
bed_shape = 0x0,200x0,200x200,0x200
before_layer_gcode = 
end_gcode = M104 S0 ; turn off Hot End\nM140 S0;\nG1 X5 Y170; \nM84     ; disable motors\n\nM42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED\nG4 P500;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P100;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P400;\nM42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
max_layer_height = 0
min_layer_height = 0.07
nozzle_diameter = 0.2
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
printer_settings_id = 
retract_before_travel = 1
retract_layer_change = 1
retract_length = 3
retract_length_toolchange = 3
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 100
serial_port = 
serial_speed = 250000
start_gcode = M42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED\nG4 P500;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P100;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P400;\nM42 S1 ; enciende el LED\n\nG28 ; home all axes
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0

[printer:Boquilla - 0.3mm]
bed_shape = 0x0,200x0,200x200,0x200
before_layer_gcode = 
end_gcode = M104 S0 ; turn off Hot End\nM140 S0;\nG1 X5 Y170; \nM84     ; disable motors\n\nM42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED\nG4 P500;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P100;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P400;\nM42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
nozzle_diameter = 0.3
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
retract_before_travel = 1
retract_layer_change = 1
retract_length = 3
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0.4
retract_restart_extra_toolchange = 0
retract_speed = 100
start_gcode = M42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED\nG4 P500;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P100;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P400;\nM42 S1 ; enciende el LED\n\nG28 ; home all axes
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
wipe = 0
z_offset = 0

[printer:Boquilla - 0.4mm]
bed_shape = 0x0,200x0,200x200,0x200
before_layer_gcode = 
end_gcode = M104 S0 ; turn off Hot End\nM140 S0;\nG1 X5 Y170; \nM84     ; disable motors\n\nM42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED\nG4 P500;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P100;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P400;\nM42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
max_layer_height = 0
min_layer_height = 0.07
nozzle_diameter = 0.4
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
printer_settings_id = 
retract_before_travel = 1
retract_layer_change = 1
retract_length = 3
retract_length_toolchange = 3
retract_lift = 0.27
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0.2
retract_restart_extra_toolchange = 0
retract_speed = 100
serial_port = 
serial_speed = 250000
start_gcode = M42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED\nG4 P500;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P100;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P400;\nM42 S1 ; enciende el LED\n\nG28 ; home all axes
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0

[printer:Boquilla - 0.5mm]
bed_shape = 0x0,200x0,200x200,0x200
before_layer_gcode = 
end_gcode = M104 S0 ; turn off Hot End\nM140 S0;\nG1 X5 Y170; \nM84     ; disable motors\n\nM42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED\nG4 P500;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P100;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P400;\nM42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
max_layer_height = 0
min_layer_height = 0.07
nozzle_diameter = 0.5
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
printer_settings_id = 
retract_before_travel = 1
retract_layer_change = 1
retract_length = 3
retract_length_toolchange = 3
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0.3
retract_restart_extra_toolchange = 0
retract_speed = 100
serial_port = 
serial_speed = 250000
start_gcode = M42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED\nG4 P500;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P100;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P400;\nM42 S1 ; enciende el LED\n\nG28 ; home all axes
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0

[printer:Boquilla - 0.6mm]
bed_shape = 0x0,200x0,200x200,0x200
before_layer_gcode = 
end_gcode = M104 S0 ; turn off Hot End\nM140 S0;\nG1 X5 Y170; \nM84     ; disable motors\n\nM42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED\nG4 P500;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P100;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P400;\nM42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
max_layer_height = 0
min_layer_height = 0.07
nozzle_diameter = 0.6
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
printer_settings_id = 
retract_before_travel = 1
retract_layer_change = 1
retract_length = 4
retract_length_toolchange = 3
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0.4
retract_restart_extra_toolchange = 0
retract_speed = 100
serial_port = 
serial_speed = 250000
start_gcode = M42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED\nG4 P500;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P100;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P400;\nM42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED\n\nG28 ; home all axes
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0

[printer:Boquilla - 0.8mm]
bed_shape = 0x0,200x0,200x200,0x200
before_layer_gcode = 
end_gcode = M104 S0 ; turn off Hot End\nM140 S0;\nG1 X5 Y170; \nM84     ; disable motors\n\nM42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED\nG4 P500;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P100;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P400;\nM42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode = 
max_layer_height = 0
min_layer_height = 0.07
nozzle_diameter = 0.8
octoprint_apikey = 
octoprint_host = 
pressure_advance = 0
printer_settings_id = 
retract_before_travel = 1
retract_layer_change = 1
retract_length = 5
retract_length_toolchange = 3
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0.4
retract_restart_extra_toolchange = 0
retract_speed = 100
serial_port = 
serial_speed = 250000
start_gcode = M42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED\nG4 P500;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P100;\nM42 S1 ; enciende el LED\nG4 P100;\nM42 S0 ; apaga el LED\nG4 P400;\nM42 S1 ; enciende el LED\nG4 P500;\nM42 S0 ; apaga el LED\n\nG28 ; home all axes
toolchange_gcode = 
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
z_offset = 0

[settings]
autocenter = 
mode = expert

[simple]
avoid_crossing_perimeters = 1
bed_shape = 0x0,200x0,200x200,0x200
bed_temperature = 0
before_layer_gcode = 
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_width = 0
complete_objects = 0
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 3
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = M104 S0 ; turn off temperature\nG28 X0  ; home X axis\nM84     ; disable motors\n
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 50%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 3
fill_angle = 45
fill_density = 70%
fill_pattern = honeycomb
first_layer_acceleration = 0
first_layer_bed_temperature = 0
first_layer_extrusion_width = 200%
first_layer_height = 0.5
first_layer_speed = 30
first_layer_temperature = 200
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 0
infill_every_layers = 10
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 80
interface_shells = 0
layer_gcode = 
layer_height = 0.3
max_fan_speed = 100
max_print_speed = 80
max_volumetric_speed = 0
min_fan_speed = 35
min_print_speed = 10
min_skirt_length = 0
notes = 
nozzle_diameter = 0.5
octoprint_apikey = 
octoprint_host = 
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 60
perimeters = 3
post_process = 
pressure_advance = 0
raft_layers = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 0
retract_length = 2
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
seam_position = aligned
skirt_distance = 6
skirt_height = 1
skirts = 1
slowdown_below_layer_time = 5
small_perimeter_speed = 15
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 20
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 0
temperature = 200
thin_walls = 1
threads = 2
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 15
top_solid_layers = 3
travel_speed = 130
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
wipe = 0
xy_size_compensation = 0
z_offset = 0